Range of single hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with an open waste outlet. Maximum working pressure 10.0 Bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2303034

Size:

Stainless steel braided thermoplastic silicone rubber (TPSiV) lined flexible hoses with 3/8" captive nut end connections.

Marking:

Axor on body

Installation Requirements:

R001 R006 R010 R009 R583

Expiry date:

31/03/2028

Model:

10 123 xxx 10 129 xxx xxx denotes the surface finish (which is a non-water contact part). examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of single hole, single outlet (fixed) electronically controlled combination tap assemblies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature set via a manual lever. The inlet adaptor to the hoses incorporates a check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2 or 3) with a built-in strainer, and the outlet incorporates an aerator. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0684 Combination Tap Assemblies

Section Subtitle:

Tap with a non-touch methods of flow control and a single inlet. Products listed in this section utilise flow control methods that do not require touch to activate.

WRAS Approval Number:

2212029

Size:

Stainless steel braided, PEX lined flexible hoses with 3/8" BSP captive nuts with a 3/8" BSP (M) x 3/8" BSP (F) adaptor

Marking:

Hansgrohe on front base of body

Installation Requirements:

R001 R006

Expiry date:

31/12/2027

Model:

15 170 XXX 15 172 XXX

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Wall mounted thermostatic shower valve, (brass body - various finishes) incorporating a ceramic disc diverter headwork controlling the flow to the hand shower or overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge a with single lever operating member which incorporates a manual override. The valve and shower head inlets incorporate stainless steel strainer washers with a flow regulator in the shower handset. The valve and shower handset inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose, handset, and overhead shower outlet. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

2010 Shower Valves

Section Subtitle:

Shower valve with thermostatic temperature control

WRAS Approval Number:

2304002

Size:

½” BSP (M)

Marking:

Hansgrohe on body

Installation Requirements:

R001 R010 R040

Expiry date:

30/04/2028

Model:

27 286 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of thermostatic cartridges with a brass housing, stainless-steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar

Non-metallic materials and components comply with BS6920 at 65°C

Section:

0442 Thermostatic cartridges

Section Subtitle:

Thermostatic cartridges for installation into specifically dimensioned tap or shower valve bodies.

WRAS Approval Number:

2304015

Size:

M42X1.5

Marking:

HG (Hansgrohe) & product information on body.

Installation Requirements:

R001

Expiry date:

30/04/2028

Model:

30742361 30742371

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of floor mounted, single hole, single outlet fixed combination taps assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.

Non-metallic materials and components comply with BS6920 at 70°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2304019

Size:

½” BSP (F)

Marking:

Hansgrohe on operating member

Installation Requirements:

R001 R010 R040

Expiry date:

30/04/2028

Model:

32 530 xxx 74 530 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and or letters, as examples: 000 = chrome optic finish, 800 = PVD steel optic finish

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company