Wall mounted two-hole, single outlet (fixed) combination tap assembly (brass body, various finishes) incorporating a ceramic cartridge headwork, single lever operating member and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0530 Combination Tap Assemblies

Section Subtitle:

Two hole tap with a single outlet and a fixed spout, incorporating a self-cancelling diverter to a shower outlet.

WRAS Approval Number:

2303070

Size:

½” BSP (M)

Marking:

AXOR on front of body

Installation Requirements:

R001 R010 R030

Expiry date:

31/03/2028

Model:

11 420 xxx AXOR Urquiola Single lever bath mixer for exposed installation Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Three-hole, single outlet, fixed combination tap assembly in chromium plated brass. Incorporating a ceramic cartridge headwork with a single lever operating member. This product also incorporates a self-cancelling diverter to a shower outlet. The shower elbow incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0655 Combination Tap Assemblies

Section Subtitle:

Three hole tap with a single outlet and a fixed spout, incorporating a self-cancelling diverter to a shower outlet.

WRAS Approval Number:

2303071

Size:

½” BSP male

Marking:

Hansgrohe on base of spout

Installation Requirements:

R001 R006 R007 R030

Expiry date:

31/03/2028

Model:

71 313 xxx Available in -000 (Chrome)

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headworks and single lever operating member. Products are supplied with lever operated pop-up wastes and spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0470 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2303339

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating 3/8” BSP captive nut end connections.

Marking:

Hansgrohe on body.

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2028

Model:

72536xxx, 72576xxx. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0510 Combination Tap Assemblies

Section Subtitle:

Two hole tap with a single outlet and a fixed spout.

WRAS Approval Number:

2303356

Size:

½” BSP (F)

Marking:

Hansgrohe on operating member

Installation Requirements:

R001 R040

Expiry date:

31/03/2028

Model:

72528xxx 72568xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes) , incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied with a lever type pop-up waste. Maximum working pressure 10.0 Bar.

Non-metallic materials and components comply with BS6920 at 70°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2303038

Size:

Stainless steel braided, PEX lined flexible hose assemblies incorporating 3/8” BSP (M) end connections.

Marking:

AXOR on Body

Installation Requirements:

R001 R006 R010 R009 R583

Expiry date:

31/03/2028

Model:

10 010 xxx 10 018 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with an open waste outlet. Maximum working pressure 10.0 Bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2303034

Size:

Stainless steel braided thermoplastic silicone rubber (TPSiV) lined flexible hoses with 3/8" captive nut end connections.

Marking:

Axor on body

Installation Requirements:

R001 R006 R010 R009 R583

Expiry date:

31/03/2028

Model:

10 123 xxx 10 129 xxx xxx denotes the surface finish (which is a non-water contact part). examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of single hole, single outlet (fixed) electronically controlled combination tap assemblies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature set via a manual lever. The inlet adaptor to the hoses incorporates a check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2 or 3) with a built-in strainer, and the outlet incorporates an aerator. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0684 Combination Tap Assemblies

Section Subtitle:

Tap with a non-touch methods of flow control and a single inlet. Products listed in this section utilise flow control methods that do not require touch to activate.

WRAS Approval Number:

2212029

Size:

Stainless steel braided, PEX lined flexible hoses with 3/8" BSP captive nuts with a 3/8" BSP (M) x 3/8" BSP (F) adaptor

Marking:

Hansgrohe on front base of body

Installation Requirements:

R001 R006

Expiry date:

31/12/2027

Model:

15 170 XXX 15 172 XXX

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Wall mounted thermostatic shower valve, (brass body - various finishes) incorporating a ceramic disc diverter headwork controlling the flow to the hand shower or overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge a with single lever operating member which incorporates a manual override. The valve and shower head inlets incorporate stainless steel strainer washers with a flow regulator in the shower handset. The valve and shower handset inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose, handset, and overhead shower outlet. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

2010 Shower Valves

Section Subtitle:

Shower valve with thermostatic temperature control

WRAS Approval Number:

2304002

Size:

½” BSP (M)

Marking:

Hansgrohe on body

Installation Requirements:

R001 R010 R040

Expiry date:

30/04/2028

Model:

27 286 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of thermostatic cartridges with a brass housing, stainless-steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar

Non-metallic materials and components comply with BS6920 at 65°C

Section:

0442 Thermostatic cartridges

Section Subtitle:

Thermostatic cartridges for installation into specifically dimensioned tap or shower valve bodies.

WRAS Approval Number:

2304015

Size:

M42X1.5

Marking:

HG (Hansgrohe) & product information on body.

Installation Requirements:

R001

Expiry date:

30/04/2028

Model:

30742361 30742371

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company

Range of floor mounted, single hole, single outlet fixed combination taps assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.

Non-metallic materials and components comply with BS6920 at 70°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2304019

Size:

½” BSP (F)

Marking:

Hansgrohe on operating member

Installation Requirements:

R001 R010 R040

Expiry date:

30/04/2028

Model:

32 530 xxx 74 530 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and or letters, as examples: 000 = chrome optic finish, 800 = PVD steel optic finish

Product Images

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Vor Heubach 1 D-77761 Schiltach

View All Listings by this Company