Range of wall mounted hose union taps (brass body or DZR brass body - see model) incorporating a non-rising spindle headwork with a ‘T’-type operating member. The CMBHUBDC-D model incorporate two approved single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 14.0 Bar. Maximum operating temperature 85°C.

Section:

1780 Taps

Section Subtitle:

Hose union tap. a. All cold water fittings located outside the thermal envelope, or those outside the building should be protected against damage by freezing. b. A servicing valve shall be fitted to the supply pipe to this fitting and shall be located within the thermal envelope of the building. Where in existing house installations a hosepipe is to be used from an existing hose union tap located outside a house and which is not provided with backflow protection, either: a. The existing hose union tap should be provided with a double check valve (Type EC or ED) located inside the building; or b. The tap should be replaced with a hose union tap that incorporates a double check valve (type HUK1); or c. A hose union backflow prevention (Type HA) or a double check valve should be continuously fitted to the outlet of the tap; or d. Is legally installed in any premises.

WRAS Approval Number:

2201101

Size:

½” BSP (M).

Marking:

CMBFHUB-D Model MID and size on body. CMBHUBDC-D, CR and size on body.

Installation Requirements:

R001 R040

Expiry date:

31/01/2027

Model:

Brass body: CMBFHUB-D DZR brass body: CMBHUBDC-D

Approval Holder:

Navigator MSL Ltd

Company Name

Navigator MSL Ltd

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company

Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

2103345

Size:

DN 6 (denoted by 06) bore diameter availble with the following end connections: 01= F1/4 02= F1/4 elbow 03= M1/4 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 19= M8*(12-110) with single O-ring 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 26= F15 29=10mm Compression fitting 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (used with copper tube manufactured to BS2871) 40=12mm pushfit isolation valve (used with copper tube manufactured to BS2871) 41=15mm pushfit isolation valve (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871) 45= M8*(12‐110) with double O‐ring 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring DN8 (denoted by 08) bore diameter availble with the following end connections: 03= M1/4 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 19= M8*(12-110) with single O-ring 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 26= F15 27=15mm smooth tube 29=10mm Compression fitting 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (used with copper tube manufactured to BS2871) 40=12mm pushfit isolation valve (used with copper tube manufactured to BS2871) 41=15mm pushfit isolation valve (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871) 43= F1/2 plastic nut 44= F3/4 plastic nut 45= M8*(12‐110) with double O‐ring 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN10 (denoted by 10) bore diameter availble with the following end connections: 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 27=15mm smooth tube 28=22mm smooth tube 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (for use with copper tube) 40=12mm pushfit isolation valve (for use with copper tube) 41=15mm pushfit isolation valve (for use with copper tube) 42=22mm pushfit isolation valve (for use with copper tube) 43= F1/2 plastic nut 44= F3/4 plastic nut 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN13 (denoted by 13) bore diameter availble with the following end connections: 04= F3/8 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 27=15mm smooth tube 28=22mm smooth tube 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 37=15mm pushfit (for use with copper tube) 38=22mm pushfit (for use with copper tube) 41=15mm pushfit isolation valve (for use with copper tube) 42=22mm pushfit isolation valve (for use with copper tube) 43= F1/2 plastic nut 44= F3/4 plastic nut 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN19 (denoted by 09) bore diameter availble with the following end connections 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 28=22mm smooth tube 32=22mm compression fitting 34=22mm isolation valve 38=22mm pushfit (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871)

Marking:

MSL, WRAS and year of manufacture (YYYY) on ferrule.

Installation Requirements:

R001

Expiry date:

31/03/2026

Model:

BFFTCW-1510 BFFTCW-1510500 BFFTCW-1512 BFFTCW-1512500 BFFTCW-10D500 BFFTCW-10D900 BFFTCW-12D500 BFFTCW-12D900 BFFTCW-DD500 BFFTCW-DD900 BFFTCWIV-10D300 BFFTCWIV-12D300 BFFTCW-1515300 BFFTCW-1515500 BFFTCW-1515900 BFFTCW-15D300 BFFTCW-15D500 BFFTCW-15D900 BFFTCW-15E300 BFFTCW-15E500 BFFTCW-15E900 BFFTCW-2222300 BFFTCW-2222500 BFFTCW-22E300 BFFTCW-22E500 BFFTCW-22E900 BFFTCWIV-15D150 BFFTCWIV-15D300 BFFTCWIV-15D500 BFFTCWIV-15E300 BFFTCWIV-15E500 BFFTCWIV-22E30

Approval Holder:

Navigator MSL Ltd

Company Name

Navigator MSL Ltd

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company

Range of flexible tap connector hoses incorporating corrugated stainless steel bodies with a blue or red PE outer sleeve and an EPDM ‘O’-ring and gasket. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 85°C

Section:

1870 Tubes

Section Subtitle:

Flexible - Metal.

WRAS Approval Number:

2307058

Size:

½” captive nut x M12 (short or long).

Marking:

MSL and batch number (L followed by date of manufacture DDMMYY) on captive nut.

Installation Requirements:

R001

Expiry date:

31/07/2028

Model:

Serpent range: BFFTCBM12LD-450 (Long - Blue - 450mm length), BFFTCRM12SD-450 (Short - Red - 450mm length).

Approval Holder:

Navigator MSL Ltd

Company Name

Navigator MSL Ltd

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company

Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

2204100

Size:

SEE MODELS

Marking:

MSL, size & ON/OFF on lever. MSL or MB, WRAS, Date of Manufacture MM/YY, DN & PN on body.

Installation Requirements:

R001

Expiry date:

30/04/2027

Model:

Red handle circlip reduced bore ball valve models: BFLBVD-15 15MM BFLBVD-22 22MM BFLBVD-28 28MM Lever Ball Valve Light Pattern – with 2 handle sleeves one red one blue BFLBVDLP-15 15MM BFLBVDLP-22 22MM BFLBVDLP-28 28MM

Approval Holder:

Navigator MSL Ltd

Company Name

Navigator MSL Ltd

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company

Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

2103347

Size:

CMFTCW-1510300 - 15mm compression x M10 CMFTCW-1512300 - 15mm compression x M12 CMFTCW-1515300 - 15mm compression x 15mm compression CMFTCW-15D300 - F1/2 x 15mm compression CMFTCW-15D500 - F1/2 x 15mm compression CMFTCW-15E300 - F3/4 x 15mm compression CMFTCW-22E300 - F3/4 x 22mm compression CMFTCWIV-15D300 - F1/2 x 15mm isolation valve CMFTCWIV-15E300 - F3/4 x 15mm isolation valve CMFTCWIV-22E300 - F3/4 x 22mm isolation valve CMFTCWP-15E300 - F3/4 x 15mm pushfit (used with copper tube manufactured to BS2871)

Marking:

MB (Brand of Navigator) WRAS and year of manufacture (YYYY) on ferrule.

Installation Requirements:

R001

Expiry date:

31/03/2026

Model:

CMFTCW-1510300, CMFTCW-1512300, CMFTCW-1515300, CMFTCW-15D300, CMFTCW-15D500, CMFTCW-15E300, CMFTCW-22E300, CMFTCWIV-15D300, CMFTCWIV-15E300, CMFTCWIV-22E300 & CMFTCWP-15E300

Approval Holder:

Navigator MSL Ltd

Company Name

Navigator MSL Ltd

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company