Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:

0470 Combination Tap Assemblies

Section Subtitle:

Single hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2110803

Size:

Stainless steel braided EPDM lined flexible hose assemblies with ½” captive nut end connections.

Marking:

NABIS ON OPERATING MEMBER

Installation Requirements:

R001 R006 R010

Expiry date:

31/10/2026

Model:

B08928 LEVICO MONO KITCHEN COMBINATION TAP ASSEMBLY

Approval Holder:

Wolseley UK

Company Name

Wolseley UK

Address

K2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926 705792

View All Listings by this Company

'581189 Center Jet Blue Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.

Section:

5510 Sealants - Screwed Joints

Section Subtitle:

General.

WRAS Approval Number:

2107566

Expiry date:

31/07/2026

Approval Holder:

Wolseley UK

Company Name

Wolseley UK

Address

K2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926 705792

View All Listings by this Company

Wall mounted bar type thermostatic mixing valve (chromium plated brass) incorporating a ¼ turn ceramic disc headwork controlling the flow with a dome type operating member and a secondary ceramic disc headwork diverting the flow between the overhead shower and hand shower with a single lever operating member. The temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. Both inlets incorporate single check valve cartridges, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The product is supplied with a fixed overhead shower, shower handset and hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

2010 Shower Valves

Section Subtitle:

Shower valve with thermostatic temperature control

WRAS Approval Number:

2110902

Size:

½” BSP (M) x ¾” BSP (M) offset union adaptor

Marking:

Nabis logo on the bar valve (Nabis is a brand of Wolseley)

Installation Requirements:

R001 R010 R040

Expiry date:

31/10/2026

Model:

D01192

Product Images

Approval Holder:

Wolseley UK

Company Name

Wolseley UK

Address

K2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926 705792

View All Listings by this Company

Two hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightner. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0550 Combination Tap Assemblies

Section Subtitle:

Two hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2007917

Size:

½” BSP (M)

Marking:

Swan logo on operating member

Installation Requirements:

R001 R006 R010

Expiry date:

31/07/2025

Model:

C58113 COMBINATION TAP ASSEMBLIES

Approval Holder:

Wolseley UK

Company Name

Wolseley UK

Address

K2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926 705792

View All Listings by this Company

Center Brand range of brass and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2202702

Marking:

CB (brand of Wolseley) and size on body

Installation Requirements:

R001

Expiry date:

28/02/2027

Model:

Center Brand range consisting of: N1 STRAIGHT COUPLING: 6mm to 54mm N1IM ADAPTOR COUPLING: 15mm x ½” to 28mm x 1” N1R REDUCING COUPLING: 8mm x 6mm to 54mm x 42mm N1SLIP STRAIGHT COUPLING SLIP: 15mm to 54mm N2 STRAIGHT FEMALE CONNECTOR: 15mm x 3/8" to 54mm x 2” N3 STRAIGHT MALE CONNECTOR: 15mm x 3/8" to 54mm x 2” N6 REDUCER: 8mm x 6mm to 54mm x 42mm N7 FEMALE ADAPTOR: 15mm x ½” to 54mm x 2” N8 MALE ADAPTOR: 15mm x ½” to 54mm x 2” N9 ADAPTOR: ½” x 15mm to ¾” x 22mm N11 UNION COUPLING CONE FACE: 15mm to 54mm N12 ELBOW: 8mm to 54mm N12R REDUCING ELBOW: 22mm x 15mm N12S STREET ELBOW: 10mm to 54mm N13 MALE ELBOW: 15mm x 1/2” to 28mm x 1” N14 FEMALE ELBOW: 15mm x ½” to 35mm x 1.1/4” N15 BACKPLATE ELBOW: 15mm x ½” to 22mm x ¾” N18 SLOW BEND: 10mm to 54mm N18S SLOW STREET BEND: 10mm to 54mm N21 OBTUSE ELBOW 45°: 12mm to 54mm N21S OBTUSE STREET ELBOW 45°: 15mm to 54mm N22 PARTIAL CROSSOVER: 15mm to 22mm N23 FULL CROSSOVER: 15mm to 22mm N24 EQUAL TEE: 6mm to 54mm N25 TEE REDUCED BRANCH: 15mm x 15mm x 10mm to 54mm x 54mm x 42mm N26 TEE ONE END REDUCED: 18mm x 15mm x 18mm to 54mm x 42mm x 54mm N27 TEE ONE END AND BRANCH REDUCED: 15mm x 12mm x 12mm to 54mm x 42mm x 42mm N28 TEE BOTH ENDS REDUCED: 10mm x 10mm x 12mm to 35mm x 35mm x 42mm N29 FEMALE TEE: 15mm x ½” x 15mm N29R FEMALE TEE: 22mm x ½” x 22mm to 28mm x ½” x 28mm N30 FEMALE TEE: 15mm x 15mm x ½” to 28mm x 28mm x 1” N30R FEMALE TEE: 22mm x 22mm x ½” to 35mm x 35mm x ½” N50 CROSS: 15mm to 22mm N61: 8mm to 54mm N61AV STOP END: 15mm N62 STRAIGHT TAP CONNECTOR: 15mm x ½” to 22mm x ¾” N63 BENT TAP CONNECTOR: 15mm x ½” to 22mm x ¾” N64 BENT UNION ADAPTOR: 15mm x ¾” N65 BENT MALE UNION CONNECTOR: 15mm x ½” to 28mm x 1” N68 STRAIGHT UNION ADAPTOR: 15mm x ¾” to 28mm x 1¼” N68FF FLAT FACED UNION ADAPTOR: 22mm x ¾” N68 METER UNION: 22mm x ¾” N69 STRAIGHT MALE UNION CONNECTOR: 15mm x ½” to 54mm x 2”

Approval Holder:

Wolseley UK

Company Name

Wolseley UK

Address

K2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926 705792

View All Listings by this Company