Section Code 1610 : Wholesome water use.
Back To Directory SectionsRange of pumps with stainless steel bodies and plastic impellers. Maximum operating pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of domestic water pressure booster pumps with brass impellors, plastic bodies and an accumulator. Models are supplied with a pressure reducing valve, isolation valve, inline strainer and non-return valve. Maximum working pressure 4.5 bar. Maximum operating temperature 35°C.
Range of cold water booster sets comprising of a multistage stainless steel pumps and manifolds with a common control panel and motor mounted inverters. Incorporating a floor standing pressure vessel fitted with a flow through valve and supplied with servicing valves on the inlet and outlet supplies to the manifold and a drain off valve. The outlet manifold incorporates a single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection) Product incorporates an expansion vessel factory pre-set at 25.0 bar. Maximum working pressure 12.0 bar. Maximum operating temperature 23°C.
Range of multistage horizontal water pumps with stainless steel bodies and impellers incorporating EPDM ‘O’-rings and seals. With various nominal flow rates depending on number of impellers and inlet connection size. Maximum working pressure 10.0 bar. Cold Water Use Only.
Range of pumps with brass bodies and EPDM ‘O’-rings. Models E1-13/94 and E1vario-13/94 incorporate spherical valves and non-return valves. Model VPMW-2/DC E-V supplied with non-return valve. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of vertical multistage pumps with stainless-steel bodies, stainless-steel impellers, intermediate chambers, shaft and outer sleeve. Cold water use only. Maximum working pressure 12.0 bar.
Range of circulator pumps with stainless steel bodies and plastic impellers. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of submersible pumps incorporating stainless-steel bodies and plastic impellers. Maximum working pressure 23.0 bar or 36.0 bar (please refer to model). Maximum operating temperature 35°C.
Helix range of vertical stainless steel multistage pumps with various pump housing materials depending on pump configuration. Maximum working pressure 30.0 bar. Cold water use only.
VDROO range of stainless steel multistage centrifugal pumps with stainless steel impellers, diffusers and outer sleeves. The pumps incorporate a Silicone Carbide and EPDM mechanical seal. Maximum working pressure 25.0 bar DIN flange. Maximum working pressure 16.0 bar for oval flange. Cold water use only.
Range of pumps incorporating a plastic body with stainless steel impellers, shaft and chambers. The inlet incorporate a stainless steel strainer. Maximum working pressure 2.4 bar (model HQ200). Maximum working pressure 3.1 bar (model HQ400). Maximum working pressure 3.3 bar (model HQ800). Cold water use only.
Range of cold water supply booster sets, incorporating a stainless steel manifold system and between 1 and 4 pumps depending on model. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels. Maximum working pressure 10.0 bar or 16.0 bar, dictated by the pump model(s) fitted. Cold water use only.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O`-rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Self-priming electric booster pump with plastic body incorporating plastic impellers with variable speed settings, and a non-return return valve (not suitable for backflow protection). Maximum working pressure 8.0 bar. Cold water use only.
Pent-A-Boost domestic break tank and booster set incorporating a single or dual pump stage pump set assembly and break cistern (incorporating an AG air gap arrangement). Inlet level sensors control the water supply via solenoid valves with inline strainers fitted (see manufacturers data sheet for optional arrangements). The unit also incorporates an expansion vessel. Flow from the break tank is via a single check valve suitable for fluid category 2 to a booster pump arrangement (see manufacturers data sheet for optional arrangements). Maximum working pressure 10 bar. Cold water use only.
“Yonos PARA Z15 and Yonos PARA Z25 ” range of circulation pumps incorporating brass bodies, plastic impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of single and twin ended shower booster pumps with plastic bodies and plastic impellers. The inlets/outlets incorporate stainless steel braided EPDM lined flexible hose assemblies with isolation valves and stainless steel strainers. The outlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The Universal Twin models incorporate an expansion vessel. Maximum working pressure (See model). Maximum operating temperature 60°C.
Range of cold water supply booster sets, incorporating a stainless steel manifold system and between 1 and 4 pumps depending on model. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels. Maximum working pressure 10.0 bar or 16.0 bar, dictated by the pump model(s) fitted. Cold water use only.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O`-rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of vertical submersible multistage pumps. Cold water use only. Open outlet use only.
Range of central heating pumps incorporating polyether sulphone impellers, copper-tin alloy body, carbon graphite axial bearings and EPDM O-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of vertical multistage booster pumps, with stainless steel bodies and impellors (AISI304 or 316 see model). Maximum working pressure (model dependent): 4.0 bar models: BMVET(I) 32-10-1 to BMVET(I) 32-40. BMVET(I) 42-10-1 to BMVET(I) 42-20. BMVET(I) 65-10-1 to BMVET(I) 65-20-2. BMVET(I) 85-10-1 to BMVET(I) 85-10. 10.0 bar models: BMVET(I) 1-2 to BMVET(I)1-36. BMVET(I) 2-2 to BMVET(I) 2-11. BMVET(I) 3-2 to BMVET(I) 3-29. BMVET(I) 4-2 to BMVET(I) 4-10. BMVET(I) 8-2 to BMVET(I) 8-20. BMVET(I) 12-2 to BMVET(I) 12-18. BMVET(I) 16-2 t BMVET(I) 16-16. BMVET(I) 20-1 to BMVET(I) 20-17. BMVET(I) 32-50-2 to BMVET(I) 32-100. BMVET(I) 42-30-2 to BMVET(I) 42-50. BMVET(I) 65-20-1 to BMVET(I) 65-30. BMVET(I) 85-20-2 to BMVET(I) 85-30-2. 15.0 bar models: BMVET(I) 2-13 to BMVET(I) 2-26. BMVET(I) 3-31 to BMVET(I) 3-36. BMVET(I) 4-12 to BMVET(I) 4-22. BMVET(I) 32-110-2 to BMVET(I) 32-140. BMVET(I) 42-60-2 to BMVET(I) 42-130-2. BMVET(I) 65-40-2 to BMVET(I) 65-80-1. BMVET(I) 85-30-1 to BMVET(I) 85-60. Maximum operating temperature 100°C.
CM(E)(C) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. (CMEC models were added October 2023). The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Cast iron models: Maximum working pressure 10.0 bar. Cold water use only. Stainless steel models: Maximum working pressure 16.0 bar. Maximum operating temperature 60°C for self-priming models, 99°C for all other models.
Range of submersible pumps with stainless steel bodies, impellers and shaft. The XPW range incorporates a strainer cowl on the suction end of the pump. The XPWA range features a stainless head which provides a threaded connection instead of the strainer. Cold water use only.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Dutypoint ‘VS’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels.. Maximum working pressure 10.0 bar. Cold water use only.
Range of positive displacement diaphragm pumps with plastic bodies, EPDM ‘O’-rings and TPE diaphragm. The product incorporates an integral bypass relief valve. For use with John Guest LLDPE Pipe. Maximum working pressure 11.03 Bar (Bypass) and 7.0 Bar (Operating). Cold water use only.
Range of pumps with either brass or stainless-steel bodies, stainless steel impellor and NBR ‘O’ rings. 20 & 33 brass series have a maximum working pressure of 16.0 bar. 33 stainless-steel series has a maximum working pressure of 20.0 bar. 22, 24 ,26, 38, 31, 32 & 34 series have a maximum working pressure of 20.0 bar. Cold water use only.
Range of circulating pumps, with plastic or stainless steel bodies (cast EN 1.4308 or plate EN 1.4301) and a plastic impeller. Maximum working pressure 10.0 bar (stainless steel bodied pumps), 3.0 bar (plastic bodied pumps). Maximum operating temperature 95°C.
Range of single stage circulating pumps with plastic impellers and stainless steel housing, (red or black external coating, and from July 2023 a yellow external coating on the 1½" model with 130mm port length). From December 2023 the UPS25 prefix models can be supplied with EPDM inlet/outlet gaskets and the UPS32 prefix models can be supplied with fibre/NBR inlet/outlet gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C (s/steel plate EN 1.4301/1.4401 models) or 99°C (s/steel cast EN 1.4308 models).
Range of booster sets with a stainless steel manifold system connecting 2 or 3 wholesome water pumps (For 2HELIX & 3HELIX models only). The set also includes spherical valves, and a non-return valve Maximum working pressure: 10.0 Bar Maximum operating temperature: 40°C
Range of single stage centrifugal pumps with bronze housings or plastic housings (see model) and plastic impellers. Maximum working pressure 6.0 bar (UP(S)(O) 15-XX CES87 130 model only), 10.0 bar (all other models). Maximum operating temperature 95°C.
Range of black plastic bodied multistage, self or manually primed, high pressure centrifugal pumps with a stainless steel outer casing, plastic impellors, EPDM seals and ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.
MBC 12-22WM & MBC 12-28WM models are wall mounted mains supply booster sets. They are supplied with two spherical isolation valves, a spherical bypass valve and two single check valve assemblies (suitable for backflow protection against Fluid Category 2). The check valve assemblies are to be installed in accordance with the manufacturers instructions, one upstream of the pump inlet and one after the bypass valve. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet and is housed within a wall mounted cabinet. MJ3 VM & MJ3 HM models are mains supply booster sets intended to be mounted on an expansion vessel (not supplied as part of the approval). They comprise of a pump, a suction and discharge manifold with bypass arrangement, and a spherical bypass valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet. Maximum working pressure 6.0 bar. Cold water use only.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of rotary vane (positive displacement) pumps with stainless steel bodies. Maximum working pressure 18.0 bar. Cold water use only.
Range of booster pumps with plastic bodies and impellers, EPDM ‘O’-rings and stainless steel inlet manifolds. The product incorporates a non-return valve. The ESYBOX MAX single models are also supplied with an optional 2” BSP (M) x 1¼” BSP (F) plastic inlet adaptor. Maximum working pressure 12.0 bar. Cold water use only.
Multistage, vertical booster pumps with a brass body and stainless steel pump housing, stainless steel impellers and EPDM ‘O’-rings. The 41782 (MV90 4M VSD) model includes a pressure transducer. Maximum working pressure 6.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel (AISI 304) bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Maximum operating temperature 90°C.
Range of magnetic drive volumetric rotary vane pumps with a plastic housing and built-in relief valve. Maximum working pressure: 22 series models - 20.0 bar, 20 series models - 14.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum operating pressure 11.0 bar. Maximum working temperature 90°C.
Range of pump units with plastic bodies and impellers, EPDM ‘O’-rings, expansion vessel with an EPDM membrane and a carbon graphite/ceramic/NBR shaft seal (bt-ar 13 bx 4ff xp). Each pump inlet incorporates a non-return valve. Single versions are standalone pumps, twin versions also include stainless steel manifolds. Maximum working pressure 10.0 bar. Cold water use only.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: EH Three phase models 85°C, EH Single phase models 55.0°C and EHsp models 35°C.
Range of self-priming pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of single stage end suction pumps with stainless steel or cast iron pump housings, EPDM ‘O’-rings and wear rings available in low-lead bronze/brass or stainless steel. Cast iron models are coated in black cathodic paint (textured finish) or black epoxy (smooth finish). The pumps are available with carbon graphite/silicon carbide mechanical shaft seal. Impellors are available in cast iron with black cathodic paint, low-lead bronze or stainless steel. The pumps are available with fixed flange, as well as loose flange (model dependent). Maximum working pressure 10.0 or 16.0 bar depending on model. Maximum operating temperatures: Stainless steel and cast iron with (smooth) epoxy coating pumps 85°C. Cast iron pumps with (textured) cathodic paint coating are cold water use only.
Centrifugal pump with a stainless steel casing and shaft, silicon carbide and EPDM shaft seals, NBR ‘O’-rings and washers. Maximum working pressure 8.0 bar. Maximum operating temperature 45°C.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of cast iron (blue epoxy coated) (G versions only) or stainless steel (all other versions - F, N, R, T) vertical multistage pumps with stainless steel impellers, shaft and outer sleeve and EPDM 'O'-rings and seals. The pumps incorporate a ceramic/carbon graphite/EPDM and stainless steel mechanical shaft seal (QBEGG). Maximum working pressures: 1-22SV models: 1SV27-1SV37 (F VERSION) - PN16 (25mm). 3SV23-3SV33 (F VERSION) - PN16 (25mm). 5SV23-5SV33 (F VERSION) - PN16 (32mm). 10SV27-10SV21 (F VERSION) - PN16 (40mm). 15SV11-15SV17 (F VERSION) - PN16 (50mm). 22SV12-22SV17 (F VERSION) - PN16 (50mm). 1SV02-1SV25 (F VERSION) - PN25 (25mm). 3SV02-3SV21 (F VERSION) - PN25 (25mm). 5SV02-5SV16 (F VERSION) - PN25 (32mm). 10SV01-10SV13 (F VERSION) - PN25 (40mm). 15SV01-15SV10 (F VERSION) - PN25 (50mm). 22SV01-22SV10 (F VERSION) - PN25 (50mm). N VERSIONS ALL MODELS - PN25 (25-50mm). R VERSION ALL MODELS - PN25 (25-50mm). T VERSION ALL MODELS - PN16 (25-50mm). 33-125SV models: 33SV1-33SV5, 33SV6/2AG150T/D & 33SV6/2AN150T/D (G or N VERSION) - PN16 (65mm). 46SV1-46SV5 (G or N VERSION) - PN16 (80mm). 66SV1-66SV5 (G or N VERSION) - PN16 (100mm). 92SV1-92SV4 (G or N VERSION) - PN16 (100mm). 125SV1-125SV6 (G VERSION) - PN16 (125mm). 33SV7-33SV10, 33SV6/1AG150T/D, 33SV6/1AN150T/D, 33SV6G150T/D & 33SV6N150T/D (G VERSION) - PN25, (N VERSION) - PN16 (65mm). 46SV6-46SV9 (G VERSION) - PN25, (N VERSION) - PN16 (80mm). 66SV6-66SV8 (G VERSION) - PN25, (N VERSION) - PN16 (100mm). 92SV5-92SV7 (G VERSION) - PN25, (N VERSION) - PN16 (100mm). 125SV7-125SV8 (G VERSION) - PN25 (125mm). 33SV10-33SV13 (G VERSION) - PN40 (65mm). 46SV10-46SV13 (G VERSION) - PN40 (80mm). Cold water use only. VERSION) - PN25 (100mm). 92SV5-92SV7 (G or N VERSION) - PN25 (100mm). 125SV7-125SV8 (G or N VERSION) - PN25 (125mm). 33SV10-33SV13 (G VERSION) - PN40 (65mm). 46SV10-46SV13 (G VERSION) - PN40 (80mm). Cold water use only.
Page 1 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
