Section Code 1535 : Tap accessories.
Back To Directory SectionsCoin type wastes with chromium plated brass body and rubber seal. Supplied with a plastic backnut.
Wall mounted shower arm with brass body (various finishes). Maximum operating temperature 85°C.
Ceiling mounted shower arm with brass bodies (various finishes) and faceplate. Maximum operating temperature 85°C.
In-wall concealed, manually accessible and operated hose connector incorporating a brass body, quarter turn ceramic disc headwork and operated by removable key. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of isolation valves incorporating brass bodies and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Tap outlet with a silicone body. Maximum operating temperature 100°C.
Chrome plated brass quick connector with EPDM washer. Maximum operating temperature 60°C.
Range of bidet spray kits comprising of a hand set with self-closing trigger, wall bracket, flexible hose assembly, thermostatic blending valve and isolation valve. Maximum working pressure 5 bar. Maximum working temperature 60°C
Angle bracket with brass body (various finishes). The inlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of spout outlets with brass bodies (various finishes) incorporating an aerator. Product is supplied with either a lever type pop up (HIRONDELLE models) or click type waste (ICON-X & CORVAIR models). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Spout end flow control device (aerator with ‘switchable’ spray formation). Maximum operating temperature 65°C.
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
Range of click type pop-up wastes with brass bodies. Maximum operating temperature 60°C.
Range of installation kits with brass bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
Wall mounted shower outlet elbow with a chromium plated brass body incorporating EPDM ‘O’-rings. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
A range of spray handsets (chrome plated plastic bodies). The outlet incorporates a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Hand spray outlet (chrome plated brass body) with a self-closing trigger assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of tap outlets with plastic bodies incorporating a filter within the body with a hollow fibre filter membrane The filters are supplied with (and must be used with) a chrome plated brass adapter which incorporates a plastic flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pull-out spray assemblies with a flexible hose and a self-closing trigger. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted installation kits with brass bodies Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
PET braided, PE/EPDM lined ‘Motion hose’, available in a range of lengths. Maximum operating temperature 70°C.
Pull-out hose assembly consisting of a chromium plated brass 45° elbow connector, a chromium plated brass HDPE lined shower hose and a nylon braided HDPE lined connecting hose. Maximum operating temperature 65°C.
Concealed wall mounted rough inset with a brass body, incorporating EDPM O-rings. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range wall mounted elbows (XX 1799 YY & XX E 1799 YY) and compression (XX 1749 YY & XX 1825 YY) fittings with brass bodies (various finishes, see models). Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted installation kits with plastic bodies. Maximum working pressure: 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Three hole, basic rough-in set with a brass body, incorporating EPDM O-ring seals. The product is supplied with a shower hose and a stainless steel braided, silicone lined flexible connecting hose. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, wall mounted rough sets with DZR brass bodies. Maximum working pressure 10.0 Bar. Maximum operating temperature 75.0°C.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
