Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'EVER-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'JSP-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
‘SIKALASTIC-836 DW & SIKAFLOOR 150’. Factory applied, off-white coloured (once mixed and applied), two-part polyurea coating system. ‘SIKAFLOOR 150’ is a two-component epoxy primer which is to be mixed in a 74:26 weight ratio and applied in accordance with manufacturer’s Product Data Sheet version ‘8’, dated May 2022. ‘SIKALASTIC-836 DW’ is a two-component polyurea coating which is to be mixed in a 1:1 volume ratio and applied in accordance with manufacturer’s Product Data Sheet version ’03.0’, dated January 2021. Cure for 24 hours at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342'. Factory applied, red coloured epoxy coating. Mix in a 3:1 weight ratio and apply in accordance with manufacturer's 'Standard Operating Procedure & Guidelines Revision 2' issue no. and date ;116/2021 15th Feb 2021'. Cure for 24 hours@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 571 ES Blue 536'. Factory applied, blue coloured polyolefin coating. Apply as per manufacturer's instructions dated '08/2022'. Cure for 20 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 451 A – CP 573 B ITT Lowara'. Factory applied, blue coloured cationic resin coating. Apply as per manufacturer's technical data sheet 'LT/I-21-090' dated 'Sep 9, 2021'. Cure for 20 minutes@180°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentathane 1000 SD'. Factory applied, grey coloured polyurethane coating. Apply as per manufacturer's instructions document referenced 'Chembur R&D/PI/05' dated '15/12/2021'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 21 of 35
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
