Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DAT-01'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 34.4:44.9:20.7. Cure for 8 hours@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kerjiwal SRC'. Factory applied, grey coloured Sulphate Resisting Cement. Mix cement, sand & water in a volume ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GMF-01'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
Page 15 of 35
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
