Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'42.5 (HSR)'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SW-02'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquafitting Blue'. Factory applied, blue coloured epoxy coating. Apply and cure as per manufacturer's instructions file number 'DLCHB-CO-001', edition 'A1', issue date '2021-April-11st'. For use with water up to 65°C.
'Korepox H.B EH3100'. Factory applied, two component, cream coloured epoxy resin coating. Mix in a 3:1 volume ratio and apply as per manufacturer's instructions dated April 2009. Cure for 7 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'DUAYEN E-39'. Factory applied, two-component, red coloured (once mixed) epoxy coating. Mix Parts A&B in a volume ratio of 79.5:20.5 and apply as per manufacturer's instructions '00.05102021'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 14 of 35
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
