Section Code 5042 : Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.
Back To Directory Sections'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1212'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (black, opaque paste) with Part B (metallic grey, opaque paste) in a 5:6 weight ratio. Cure for 16 hours@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. There are two ways the coating may be prepared: First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1, apply and then cure for 2 days@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1, apply and then cure for 2 days@30°C. OR: First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1, apply and then cure for 14 days@10°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1, apply and then cure for 14 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 2 of 9
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
